As a general rule, most motorcycle rear shocks require two to three preload clicks per ten kilos of extra load, but the precise number depends on your spring rate, shock design, and how far from your baseline sag you start. This range gives you a practical starting point, though the only way to confirm you have it right is to measure your sag after each adjustment.
The relationship between preload, spring rate, and actual ride height is more nuanced than a single number suggests. Understanding what preload actually does mechanically will help you apply that rule correctly and avoid the common mistake of using preload to compensate for the wrong spring entirely. The sections below walk through each piece of the puzzle, from the physics of preload to when clicks alone are no longer enough.
How does preload actually affect how your suspension behaves?
Preload sets the initial compression of your spring before any load is applied. It does not change how stiff the spring feels during travel, that is determined by the spring rate. What preload does is raise or lower the ride height by adjusting the position at which the spring begins to work, which directly controls how much suspension travel remains available once the bike is loaded.
Think of it this way: your spring has a fixed amount of force per millimetre of compression. Preload winds that spring tighter before the wheel even touches the ground. The spring rate stays identical, but the point at which the suspension sits under load shifts upward. More preload means higher ride height and more available travel below the static position. Less preload means the suspension sits lower and compresses more easily under the same weight.
This is why preload is the primary tool for suspension setup when load changes. It keeps the spring working in its optimal range of travel regardless of whether you are riding solo, carrying luggage, or taking a passenger. Without correct preload, the suspension either sits too low and bottoms out under load, or sits too high and becomes harsh and unresponsive over small bumps.
How many preload clicks do you need per ten kilos of extra load?
For most adjustable rear shocks, a practical starting point is two to three preload clicks for every ten kilos of additional load. This applies to luggage, a passenger, or any combination of the two. Front forks with preload adjusters typically follow a similar ratio, though their click increments vary more widely between manufacturers.
The reason this range exists rather than a single fixed number comes down to spring rate. A stiffer spring, common on adventure bikes set up for loaded touring, changes geometry less per click than a softer spring designed for solo riding. On a shock with a high spring rate, you may need three or even four clicks to achieve the same sag correction that two clicks would give you on a softer setup.
What the clicks actually represent
Each click on a preload adjuster typically moves the spring seat by a fraction of a millimetre. Depending on the shock design, one full rotation of the adjuster ring might equal anywhere from one to three millimetres of spring preload change. Manufacturers rarely publish this figure, which is why measuring sag, rather than counting clicks alone, is the only reliable verification method.
Practical limits of click-based adjustment
Most shocks offer between five and fifteen clicks of preload range. That range is designed to accommodate normal variation in rider weight and light load changes. If you find yourself at the maximum preload setting and still cannot achieve correct sag, the spring rate is too soft for your combined weight and load. Adding more preload clicks beyond the designed range does not solve a spring rate mismatch, it only masks it while reducing available suspension travel.
What counts as ‘extra load’ when adjusting preload?
Extra load for preload adjustment purposes means any weight added to the bike beyond the baseline at which your suspension was originally set up. This includes the rider in full gear, any passenger, luggage on the bike, and accessories like tank bags or tail packs. All of it compresses the spring and affects your sag measurement.
The most common mistake adventure riders make is treating rider weight as a constant and only accounting for luggage. In practice, your suspension should be set with you on the bike in your typical riding gear, because the rider represents the single largest variable in most setups. A 70 kg rider and a 90 kg rider on the same bike need meaningfully different preload settings even with no luggage at all.
When preparing for a loaded tour, add up the following before adjusting your suspension preload:
- Your weight in full riding gear
- Passenger weight if applicable
- Panniers, top box, and their contents
- Tank bag, handlebar bag, or tail pack
- Any additional accessories mounted to the frame or subframe
The total of these figures is your working load. Compare it to the weight at which your baseline sag was established, and the difference is what you need to compensate for with your preload adjustment.
How do you measure sag to verify your preload setting is correct?
To verify your preload setting, measure rider sag, the difference in rear suspension height between the bike fully unloaded and the bike with the rider seated in the normal riding position. For most adventure bikes and dual-sport machines, correct rider sag falls between 25 and 35 millimetres at the rear. Front sag is typically slightly less.
Here is how to measure rear sag accurately:
- Place the bike on a paddock stand or have an assistant hold it upright on a flat surface
- Measure from a fixed point on the rear subframe or mudguard directly down to the axle, note this as your free sag measurement
- Have the rider sit on the bike in full gear in the normal riding position, feet on the pegs
- Measure the same point again, this is your rider sag measurement
- Subtract the second measurement from the first, the result is your rider sag in millimetres
If rider sag is more than 35 mm, increase preload. If it is less than 25 mm, reduce preload. Adjust in small increments and remeasure after each change. When adding significant load such as full touring luggage, repeat this process with that load on the bike to confirm the setting holds within the target range.
Free sag, the amount the suspension drops under the bike’s own weight without a rider, should also be checked. If free sag is zero (the suspension does not drop at all when taken off the stand), the spring is too stiff or preload is excessive. If free sag is more than about 10 to 15 mm, the spring may be too soft for the load.
When should you go beyond click adjustments and change the spring?
You should consider changing the spring when you cannot achieve correct sag within the available preload range, or when the suspension feels consistently too stiff or too soft throughout the travel regardless of preload setting. Preload adjustments shift ride height, they do not change how the suspension responds to bumps, impacts, or high-speed compression. That is the spring rate’s job.
The clearest signs that a spring change is needed rather than a preload adjustment include:
- You are at maximum preload and sag is still excessive
- You are at minimum preload and the ride is still harsh with correct sag
- The suspension bottoms out on moderate impacts even with preload increased
- Ride quality changes dramatically between solo and loaded riding despite correct sag in both configurations
- Your total riding weight has changed significantly since the bike was originally set up
For adventure bike suspension used across a wide range of loads, a progressive-rate spring or a spring specifically rated for your combined weight range will outperform any amount of preload tuning on a spring that was never matched to your use case. This is especially relevant for riders who regularly switch between solo commuting and fully loaded multi-day tours, the load difference can exceed 40 kilos, which is well beyond what preload clicks alone can reliably accommodate.
How TFX Suspension Helps You Get Preload Right
Getting preload dialled in correctly is straightforward when your shock is built around your actual riding weight and load profile from the start. That is exactly how we approach every suspension build at TFX Suspension. Rather than offering a generic off-the-shelf unit that you then try to adjust into shape, we configure each shock to match the rider, the bike, and the intended use before it leaves our workshop.
Here is what working with us looks like in practice:
- Spring rate matched to your load: We select or wind a spring rated for your combined rider and luggage weight, so preload adjustment works within its intended range rather than compensating for a mismatch
- Custom preload range: Our shocks are built with a preload range calibrated to your specific load variation, whether you ride solo, two-up, or fully loaded
- Sag setup included: We provide target sag figures and setup guidance specific to your unit, so you know exactly what to aim for when adjusting in the field
- Full service and retuning support: If your riding weight or load profile changes, we can rework the setup rather than leaving you to guess at click counts
Whether you ride a CFMoto adventure bike, a mainstream dual-sport, or something more specialised, we build suspension that performs across the full range of conditions you actually ride in. Explore our suspension shop to find the right unit for your bike, browse our CFMoto-specific suspension options, or visit the TFX Suspension homepage to learn more about how we build. If you want to talk through your specific load setup and what spring rate makes sense for your riding, contact us directly and we will help you get it right.
Frequently Asked Questions
Can I adjust preload while the bike is loaded, or do I need to unload it first?
You can make preload adjustments with the bike loaded, but you should always measure sag in the configuration you intend to ride in. The most practical approach is to set your baseline preload unloaded, then remeasure sag once the bike is fully packed and you are seated in riding gear. Make any fine-tuning clicks with the load on the bike, then verify with a fresh sag measurement before heading out.
What if I don't have a paddock stand — is there a way to measure sag accurately on my own?
Yes, you can measure sag without a paddock stand by using a wall or fence for balance instead of an assistant. For the unloaded measurement, lean the bike on its side stand, lift it vertical, and quickly measure before it settles — or use a zip tie on the shock shaft as a travel indicator. The zip tie method is particularly useful for solo riders: push the suspension fully up, slide the zip tie to the seal, then sit on the bike and check how far the tie has moved down the shaft.
How often should I re-check and re-adjust my preload settings?
Recheck your preload any time your load changes by more than around 10 kilos, which covers adding or removing luggage, riding two-up, or a significant change in your own weight. It is also worth checking sag at the start of a multi-day tour, since luggage weight shifts as consumables are used. Springs can also settle slightly over time, so an annual sag check as part of your suspension service routine is good practice.
Is front preload adjustment just as important as rear, and should I adjust both together?
Front preload matters for maintaining balanced ride geometry, but the rear is the priority for load-related adjustments because that is where most of the extra weight sits on a loaded adventure bike. As a general rule, if you increase rear preload significantly to compensate for a heavy load, adding one or two clicks of front preload helps maintain the bike’s overall balance and steering feel. Always set the rear first, then adjust the front to match the chassis attitude.
My shock only has a spring preload collar with no click detents — how do I make repeatable adjustments?
On shocks with a smooth threaded collar rather than click detents, use a paint pen or correction fluid to mark your baseline position on both the collar and the shock body before making any changes. Count full or half rotations when adjusting, and note that one full rotation typically changes preload by one to three millimetres depending on the thread pitch. Always measure sag after adjusting rather than relying on rotation count alone, since thread pitch varies significantly between manufacturers.
Can too much preload actually damage my shock or spring over time?
Running at maximum preload for extended periods does not typically damage a quality shock, but it does indicate a spring rate mismatch that will compromise performance and potentially accelerate wear. Excessive preload reduces available suspension travel, which increases the likelihood of bottoming out — and repeated hard bottoming can damage the shock internals over time. If you consistently need maximum preload to achieve correct sag, a heavier spring is the right fix, not continued use at the adjuster’s limit.
What is the difference between preload adjustment and ride height adjustment, and are they the same thing?
They are related but not identical. Preload adjustment changes ride height as a byproduct of altering how compressed the spring is at rest — more preload raises the rear, less lowers it. True ride height adjustment on some shocks is done via a separate linkage or clevis length change, which alters geometry without affecting spring preload. For most riders using standard adjustable shocks, preload is the only ride height tool available, which is why understanding its limits is important before assuming a ride height problem is a preload problem.
Configure Your Motorcycle Suspension
Find the correct TFX suspension setup for your motorcycle in less than 60 seconds.
Start Configuration


