After increasing preload, you should have between 25 and 40 mm of static sag remaining on the rear shock, and between 30 and 40 mm on the front forks. Preload does not eliminate sag; it controls how much the suspension compresses under the weight of the bike alone, without a rider. Getting this balance right is the foundation of a well-performing motorcycle suspension setup.
These figures apply to most street and adventure motorcycles, though the ideal range shifts slightly depending on the bike’s weight, geometry, and intended use. The sections below walk through how preload and static sag interact, how to measure sag correctly, and when your numbers are telling you something is wrong.
What Happens to Static Sag When You Increase Preload?
When you increase preload, static sag decreases. Preload compresses the spring before any weight is applied, which means the suspension starts from a higher position and sags less under the bike’s own weight. The relationship is direct: more preload equals less static sag, less preload equals more static sag.
It is important to understand that preload does not change the spring’s stiffness; it only changes the spring’s starting position. A stiffer spring rate will reduce sag more effectively than preload alone. If you are winding preload to its maximum and still have too much sag, the spring rate is likely too soft for your weight and riding style.
On most motorcycles, preload is adjusted via a threaded collar or adjuster on the shock body and at the top of the fork legs. Turning the adjuster clockwise typically increases preload. Even small adjustments, a few millimetres of preload change, can noticeably shift your static sag reading, so it pays to make changes gradually and re-measure each time.
What Is the Correct Static Sag Range for Most Motorcycles?
For most motorcycles, the correct static sag range is 25 to 40 mm at the rear and 30 to 40 mm at the front. Adventure bikes and dual-sport machines often sit toward the higher end of this range to accommodate varied terrain and heavier loads. Sport bikes typically run less sag for sharper handling response.
These numbers exist for a practical reason: they ensure the suspension has enough travel in both directions. Too little sag means the suspension is sitting too high and will run out of compression travel over bumps. Too much sag means the bike sits low and will run out of rebound travel, causing the suspension to bottom out or the wheel to lose contact with the ground.
Rider sag, sometimes called race sag or laden sag, is a related measurement taken with the rider seated in full gear. Rider sag typically falls between 25 and 35 mm for the rear on most motorcycles. Static sag and rider sag together give you the full picture of how your suspension is behaving under real conditions.
How Do You Measure Static Sag Accurately?
To measure static sag accurately, you need a tape measure, a helper, and a consistent measurement point. The process takes less than ten minutes and should be repeated any time you adjust preload or change your riding load.
- Lift the bike off the ground: Fully extend the suspension by lifting the rear of the bike or placing it on a paddock stand. Measure the distance from your reference point, typically the rear axle, to a fixed point directly above it on the subframe or mudguard. Record this as measurement A.
- Lower the bike onto its wheels: Let the bike settle on both wheels with no rider. Bounce the suspension gently a few times to let it settle into its natural position. Measure the same distance again. Record this as measurement B.
- Calculate static sag: Subtract B from A. The result is your static sag. For example, if A is 320 mm and B is 290 mm, your static sag is 30 mm.
- Repeat for the front: Use the same method on the front forks, measuring from the bottom of the lower fork leg to the top of the dust seal or a mark you make on the stanchion.
Consistency matters here. Use the same measurement points every time, and always measure vertically rather than at an angle. Even a slight angle can introduce enough error to throw off your reading by several millimetres.
What Does Too Little Static Sag After Preload Adjustment Indicate?
Too little static sag, typically less than 20 mm at the rear, after preload adjustment usually indicates that the spring rate is too stiff for the bike’s unloaded weight, or that preload has been set too high. When static sag is too low, the suspension sits high and the bike’s geometry shifts in ways that affect steering and stability.
A suspension that sits too high will feel harsh over small bumps because the spring is already compressed and has limited compliance left. On adventure bikes, this can make rough tracks uncomfortable and reduce traction on loose surfaces, where the wheel needs to track the ground rather than skip over it.
If reducing preload to its minimum setting still leaves you with less than 20 mm of static sag, the spring rate is too stiff for your application. This is common when a bike has been set up for a heavier rider and then ridden by someone lighter, or when aftermarket springs have been fitted without accounting for the rider’s weight. In these cases, fitting a softer spring is the correct solution, not simply removing preload.
Should Static Sag Change When Carrying Luggage or a Passenger?
Yes, static sag will change when you add luggage or a passenger, because the additional weight compresses the suspension further. This is expected and normal. The key is to re-check your sag figures whenever your load changes significantly, and to adjust preload accordingly to bring sag back into the correct range.
For adventure riders carrying full touring luggage, panniers, a top box, and a tank bag, the added weight can easily reduce rear static sag by 10 to 20 mm compared to an unladen setup. Without adjusting preload, the bike will sit lower, the geometry will change, and handling will feel sluggish or vague, particularly in corners.
When riding two-up with a passenger, the rear suspension is under considerably more load. Most manufacturers recommend increasing rear preload for two-up riding, and some bikes include a dedicated two-up preload setting on the shock adjuster for this reason. After adding preload for a passenger, always verify that static sag is still within the 25 to 40 mm range.
A practical approach for adventure touring is to set your suspension for your most common load, typically solo with moderate luggage, and note how many turns of preload adjustment you need to add for a fully loaded or two-up configuration. This way, you can switch between setups quickly without measuring from scratch each time.
How We Help You Get Your Suspension Setup Right
At TFX Suspension, we take the guesswork out of suspension setup. Whether you are dialling in static sag for solo touring or configuring your adventure bike for two-up riding with full luggage, we build and tune suspension systems around your specific weight, riding style, and terrain. Here is what we offer:
- Custom spring rate selection: We match the spring rate to your actual weight and load, so preload adjustment works within the correct range from the start.
- Full preload and damping setup: Every shock and fork set we supply comes configured to your specifications, not a generic factory baseline.
- Suspension for your specific bike: From mainstream adventure bikes to CFMoto models, we have solutions across a wide range of platforms.
- Maintenance and revalving: If your existing suspension is worn or no longer suits your riding, we offer full service and custom tuning to bring it back to optimal performance.
- Expert advice before you buy: Not sure what you need? Get in touch with us and we will help you work out the right setup before you spend a penny.
If you are ready to stop compromising on comfort and control, browse our suspension range or visit TFX Suspension to find out how a properly set-up system transforms the way your motorcycle rides.
Frequently Asked Questions
Can I set static sag correctly without a helper?
It is possible to measure static sag solo, but accuracy suffers without someone to hold the bike upright and take measurements at the same time. A common workaround is to use a zip tie or tape to mark your reference point on the fork stanchion before and after settling the bike, then measure the difference. That said, having a helper is strongly recommended for consistent, repeatable results — even a small amount of lean can skew your reading by several millimetres.
How often should I check and re-adjust my static sag?
You should check static sag any time your load changes significantly, such as when adding luggage, riding two-up, or fitting new suspension components. Beyond that, it is good practice to verify your sag at the start of each riding season, since springs can settle slightly over time and after extended use. If your bike’s handling feels different from one ride to the next without an obvious cause, checking sag is always a sensible first diagnostic step.
What is the difference between static sag and rider sag, and do I need to measure both?
Static sag measures how much the suspension compresses under the bike’s weight alone, while rider sag (also called race sag or laden sag) measures compression with the rider seated in full gear. Both measurements matter because they give you a complete picture of suspension behaviour — static sag tells you whether your spring rate and preload are in the right ballpark, while rider sag confirms how the suspension is actually performing under real riding conditions. Ideally, you should measure both and use them together to fine-tune your setup.
My preload adjuster is already at maximum but I still have too much sag — what should I do?
If you have wound preload to its maximum and your static sag is still above 40 mm at the rear, the spring rate is too soft for your weight and load — adding more preload cannot fix a fundamentally mismatched spring. The correct solution is to fit a stiffer spring rated appropriately for your weight. Continuing to run maximum preload without addressing the spring rate can cause handling instability, premature bottoming out, and uneven tyre wear, so it is worth getting the spring rate properly matched rather than working around it.
Does adjusting front preload affect the bike's steering or geometry?
Yes, front preload adjustments directly influence the bike’s geometry and steering behaviour. Increasing front preload raises the front of the bike, which slackens the steering geometry slightly and can make the steering feel more stable but less responsive. Reducing front preload lowers the front end, steepening the geometry and quickening the steering. This is why front and rear sag should always be considered together — changes to one end of the bike affect the overall balance and handling characteristics.
Is there a risk of damaging my suspension by setting preload incorrectly?
Running extreme preload settings — either too high or too low — will not typically cause immediate mechanical damage, but it can accelerate wear over time and lead to poor handling that increases rider fatigue and safety risk. Excessive preload without an appropriate spring rate puts the spring under constant unnecessary stress, while too little preload can cause the suspension to bottom out repeatedly, which is hard on the internals of both shocks and forks. Getting sag within the correct range protects your components as well as improving ride quality.
Can I use the same preload settings year-round, or do I need to adjust for temperature and conditions?
Preload itself is not significantly affected by temperature, but damping behaviour can change noticeably in cold weather as fork oil and shock fluid thicken. If your suspension feels noticeably stiffer in winter, that is more likely a damping issue than a preload issue. However, if your riding conditions or load change seasonally — for example, switching from solo commuting to loaded summer touring — it is worth re-checking your sag figures and adjusting preload to suit the new setup.
Configure Your Motorcycle Suspension
Find the correct TFX suspension setup for your motorcycle in less than 60 seconds.
Start Configuration


